Interface-Technology

Power supply

Electronic for DC – and EC – Engines

Electronic Load Relay DC

The German produced parts are used everywhere, where high reliability is necessary. Here a selection of applications.

These parts are manufactured at the german company Kaleja.    Kaleja - logo1

 

kal-2Application: kal-1

- mechanical engineering
- Switch board engineering
- Package engineering
- Automation engineering
- Drive system engineering
- Medicine engineering
- Climate engineering

Products:

- Transfer modules
- Coupling relay in Module technology
- Relay modules
- Electronic Load Relays AC
- Electronic Load Relays DC
- Relay-, Diodes– and Mounting modules
- Sensor-/switch amplifier
- Logic circuits in Module technology
- Engine control
- Time modules
- Power Supply
- AC-DC / DC-DC Converter
- Rectifier Modules 

kal-3Switch mode power supply for industrial application

at module technical to snap onto DIN-rail
with Wide-Range-Input:100VAC to 256 VAC
Output voltage 12 VDC or 24 VDC
Output power 5 - 10 – 11 –22 – 25 – 50 – 100 Watt
Can be snapped at the Din-rail
 

 

kal-8AC/DC – DC/DC Converter

at Module technology
Construction width, 22,5mm
Input Voltage: 8 – 24V AC/DC
Output Voltage: 5 – 8  - 9 – 10 – 12 – 15 – 18 – 24 VDC
Can be snapped at the Din-rail

 

kal-4Motor-speed control direction of rotation control

Motor voltage 24 VDC
Power range up to 250 Watt
Max load current 3- 5- 6 – 8 A
Properties of the circuit 
Current control, Dynamical braking
Temperature Protection, Speed control
Can be snapped at the DiIN-rail

 

kal-5Electronic load relay in Printrelay case

Threshold voltage 24 DC
Switching current load circuit 5 ADC

 

 

 

kal-6Electronic load relay DC

Construction width: 12 - 17 mm
Without Cradle-Bridge-Connection
Threshold voltage 5 - 12 - 24 VDC
Switching current-load circuit
0,8 - 2,5 - 24ADC 115 - 230 VAC
Can be snapped at the Din-rail

 

kal-7Motor-speed control for brushles motors DC, direction of rotation control

otor voltage 24 VDC
Max loda current 3,5 A
Properties of the circuit 
Dynamical braking, current control
Speed control, Temerture protection
Can be snapped at the Din-rail

 

kal-9Coupling relays

Construction width:11,5 - 17- 22,5 mm
1 or 4 CO contact and 1NO or 1 NC contact
Coil voltage / threshold voltage 12 or  24 VAC/DC
115 or230 VAC  Signal current 10mA – 2 A
Output circuit: Load current 1A-8A
Can be snapped at the Din-rail

 

 

 

kal-10Sensor amplifier

Sensor-/switching amplifier 12VDC/24VDC
1 switching channel with 1 CO contact and
5 switching channel with 1 CO contact
for switching current from 8A
Supply Voltage: 12 – 24 – 230 VAC kal-11
Constructions width  22,5 and 45 mm
Can be snapped at the Din-rail

 

kal-12Relay Module

Relay module with Plug-in socket and Plug-In Pin
Implementation for large load current ( 8A to 12A )
With Status indicator  LED 3mm yellow
Module with screw terminal or with spring terminal (F)
Coil voltage-driving circuit 12V or 24V
Relay per module 2 to 16 Relay kal-13
Can be snapped at Transfer module
with Subminiature-D pin strip
with Subminiature-D contact strip
with ribbon cable connection
Customer specific Connector
Pin block on screw terminal 1:1 leaded
With screw locking 4-40 UNC
Status indicator LED 3 mm yellow
Can be snapped at the Din-rail

 

kal-15Dioden Module and Mounting Module

Single Diode 1N4007 at screw terminal leaded
Diode 1N4007 with common anode or common cathode
6 – 10 – 12 – 16 – 20 - 30 Diode
Can be snapped at the DIN-rail

 

Transfer module with Subminiature-D pin strip with Subminiature-D contact strip with ribbon cable connection Customer specific Connector kal-14

Pin block on screw terminal 1:1 leaded
With screw locking 4-40 UNC
Status indicator LED 3 mm yellow
Can be snapped at the Din-rail

 

kal-16Electronic Load Relay AC

Construction width 12 mm with and without cradle Bridge connection.
Switching current 1.5 A—2 A
Threshold Voltage 5-12-24-48 VDC
                             115-230 VAC

 

kal-17Single Phase Power Supply 2A to 10 A

Primary connection for unregulated and regulated
115 VAC or 230 VAC or 400 VAC
Residual ripple smaller than 5%. Linear regulated version smaller than 0.1%. Can be snapped at the DIN-Rail or screw mounting.
Output Voltage:
12 VDC or 24 VDC unregulated
5-10-12-24 VDC regulated

GEDO-LOGO-USA-2-kl-202
Interface Technology